Tools
Microphone test
Check that your mic works, see how loud you come through, catch clipping, hear a recording of yourself and measure how much background noise gets in. Works with headset mics, USB microphones and laptop mics.
Microphone test
Everything runs inside this tab. The page reads your microphone only after you press Start, nothing is uploaded or saved on a server, and test recordings stay in your browser until you close or reload the page.
When you press Start microphone, the browser asks whether this site may use your microphone. Choose Allow. If you have several microphones, you can pick the one to test after that. Press Stop at any time to switch the microphone off again.
1. Live level
dBFS means decibels below the loudest level the browser can represent (0 dBFS). The bright bar is the average level, the light bar is the peak and the white line holds the recent peak. When you talk at normal volume, peaks landing roughly between -20 and -6 dBFS is a comfortable target; that range is this page's rule of thumb, not a standard. Clipping means the signal hit the top and will sound distorted. These are browser readings after any processing below, not calibrated measurements.
2. Waveform and frequency spectrum
Waveform: roughly the last 40 to 50 ms of sound. Dashed lines mark full scale.
Spectrum, 50 Hz to 16 kHz.
A steady thin spike when you are silent is usually hum from power or a ground loop (often at 50 or 60 Hz and their multiples). A wide raised floor is fan or room noise. Your voice mostly fills the area from about 100 Hz up to a few kHz.
3. Record and play back
Start the microphone first.
Say a sentence at your normal gaming volume, then listen back on headphones. The clip lives in this tab's memory only; it is never uploaded. It is recorded with the processing options below, so it sounds close to what a browser voice call would send, but Discord and games apply their own processing on top.
4. Background noise and signal-to-noise
Step 1: stay quiet for 3 seconds
Noise floor: —
Step 2: talk normally for 5 seconds
Speaking level: —
Run both steps to see a signal-to-noise estimate.
The estimate is speaking level minus noise floor, both measured by the browser in dBFS. The 0–100 score maps 10 dB to 0 and 50 dB to 100 and only compares runs on this page. Noise suppression and auto gain change both numbers, so compare runs with the same settings. It is not a calibrated microphone measurement.
5. Browser voice processing and reported settings
Start the microphone to see what the browser reports.
Changing a switch restarts the microphone with the new request. The "reported" rows are what the browser says it actually applied, which can differ from what the page asked for. These switches only affect this page; Discord, games and other apps have their own versions of the same features.
6. Hear yourself (optional)
You will hear a small delay; that is normal for a browser and does not mean the microphone is slow.
How to use the microphone test
- Press Start microphone and choose Allow when the browser asks. The page cannot hear anything before that, and Stop and release mic switches it off again.
- If you have more than one microphone, pick the one you want from the Microphone list. Names appear only after you allow access; that is how browsers protect your privacy.
- Talk at the volume you use in game. Watch the level meter: the bar should jump well into the meter when you speak, and the clipping light should stay off. A flat bar means the page receives silence from that device.
- Record a clip of 5 or 10 seconds and play it back on headphones. Listen for hiss, hum, keyboard noise, a muffled sound or distortion on loud words.
- Run the two noise steps: stay quiet for 3 seconds, then talk for 5 seconds. The page shows your noise floor, your speaking level and a signal-to-noise estimate, so you can compare mic positions or settings.
Microphone not detected or blocked: how to fix it
In the browser
- If you clicked Block by mistake, click the icon at the left of the address bar, set the microphone permission for this site to Allow and reload the page.
- Browsers only let pages use the microphone over a secure (https) connection, and some block it inside embedded frames. Open this page directly in a normal tab.
On Windows
- Privacy settings. On Windows 11, open Settings, then Privacy & security, then Microphone. Turn on Microphone access, Let apps access your microphone andLet desktop apps access your microphone. Browsers, Discord and most games count as desktop apps. On Windows 10 the same switches are under Settings, then Privacy, then Microphone.
- The right input. Open Settings, then System, then Sound, and look under Input. Select the microphone you are actually using. A webcam, a monitor, a USB dongle and a headset can all show up as separate inputs.
- Disabled devices. Press Win + R, type
mmsys.cpland open the Recording tab. Right-click the empty area and turn on Show Disabled Devices. If your mic is listed as disabled, right-click it and choose Enable.
On a Mac
Open System Settings, then Privacy & Security, then Microphone, and switch on access for your browser (and for Discord or the game if those are the problem). Then open System Settings, then Sound, then Input, and select the microphone you want to use.
Hardware
- Check mute switches, inline remote buttons and flip-up booms. Many headsets mute the mic when the boom is raised.
- A headset with one four-contact 3.5 mm plug carries both the headphones and the mic. On a PC with separate pink and green jacks, it needs a splitter adapter, or the mic will not be connected at all.
- On most Bluetooth headsets, using the microphone switches the headset to a call mode, which lowers sound quality for both directions. A USB or wired connection avoids that. Myheadset setup guide explains the difference.
- If the error says the mic is in use or could not be opened, close other apps that use it, then unplug and plug it back in.
Mic too quiet, too loud or noisy
- Too quiet. On Windows 11, open Settings, then System, then Sound, select your mic under Input and raise Input volume. In the classic panel (
mmsys.cpl, Recording tab, Properties, Levels), some drivers also offer a Microphone Boost setting. Boost raises noise as well as your voice, so add a little at a time and test again. On a Mac, use the Input volume slider in Sound settings. - Too loud or clipping. Lower the input volume until the clipping light stays off on your loudest shouts. Clipped audio cannot be fixed later by turning it down.
- Position. A headset boom works best a short distance from the corner of your mouth, slightly to the side so breath does not hit it directly. Moving a desk mic closer raises your voice compared with room noise, which usually helps the signal-to-noise estimate more than any setting. My guides tohow a headset microphone picks up sound andUSB gaming microphones go into why.
- Hum or buzz. A steady spike in the spectrum when you are quiet usually comes from power or a ground loop. Try another USB port, a different cable, or unplug a charger nearby.
Mic works here but not in Discord or a game
If the meter on this page moves, Windows or macOS and the browser can hear the microphone. When another app stays silent, the problem is that app's settings or permission:
- Discord: open User Settings, then Voice & Video. Choose the same microphone as the Input Device instead of relying on Default, check Input Volume, and look at the input mode: with Push to Talk you need the key held, and with Voice Activity the input sensitivity decides when you are heard. Discord's own mic test on that page helps confirm it.
- Games: most games have a voice chat device and volume in their audio settings, and many use the Windows default device. In
mmsys.cpl, Recording tab, you can set your mic as both theDefault Device and the Default Communications Device. - Permissions: on Windows, check Let desktop apps access your microphone; on a Mac, check that the app is switched on under Privacy & Security, then Microphone.
- If your headset's own software adds noise cancelling or a voice effect, it can fight with the same features in Discord. Try one at a time.
Once the mic is sorted, check the other half of your headset with thespeaker and headset test. If you are thinking about an upgrade to an XLR microphone, see what a gaming audio interface does.
Common questions
How do I test my microphone online?
Press Start microphone on this page and allow access when the browser asks. Talk and watch the level meter move, then record a short clip and play it back. If the meter moves, the browser is receiving sound from that microphone. If it stays flat, check the device list, mute switches and the permission steps below the tool.
Is my voice recorded or uploaded?
No. The level meter, spectrum and measurements are calculated inside your browser. A test recording is kept only in the memory of this tab and disappears when you delete it, reload or close the page. You can save it to your own computer with Save clip if you want to keep it.
Why does the page say no microphone was found?
The browser could not see any input device. Check that the microphone or headset is plugged in properly, that the system lists it as an input device, and that a hardware mute switch is not cutting it off. A headset with a single four-contact plug needs a splitter on a PC that has separate microphone and headphone jacks.
What is a good microphone level in dBFS?
0 dBFS is the loudest level a digital signal can reach, so readings are negative. When you talk normally, peaks somewhere around -20 to -6 dBFS give room before clipping while staying clearly above background noise. That range is a practical rule of thumb for this page, not a standard, and apps such as Discord may change your level again with their own processing.
My mic works here but not in Discord or a game. Why?
Each app chooses its own input device and applies its own settings. In Discord, check the Input Device and Input Volume in User Settings under Voice and Video, and its input sensitivity or push-to-talk setting. In games, check the voice chat device setting. On Windows, also make sure desktop apps are allowed to use the microphone in the privacy settings.
Should I turn noise suppression and echo cancellation on?
For calls on speakers, echo cancellation stops other people hearing themselves, and noise suppression helps in a loud room. With a headset in a quiet room, you can try them off and compare the recordings. Use the switches on this page to hear the difference; the reported rows show what the browser actually applied.
How accurate is the signal-to-noise score?
It is a relative, uncalibrated browser estimate. It compares your speaking level with the background noise as the browser hands them to the page, after any noise suppression or auto gain. It is useful for comparing positions, settings or microphones on the same computer, not as a lab measurement or a rating of the microphone itself.
Related tools and guides
- Sensitivity converter — Convert sensitivity between Overwatch, Valorant, CS2, and other titles using documented yaw values.
- cm/360 calculator — Turn mouse DPI and in-game sensitivity into centimeters per 360° turn.
- eDPI calculator — Multiply mouse DPI by in-game sensitivity for a same-game comparison number.
- FOV converter — Convert horizontal and vertical FOV across 4:3, 16:9, 16:10, and 21:9. Includes Overwatch, CS2, and Valorant.
- Frame-time and Hz calculator — Convert FPS to milliseconds, compare that wait to the monitor refresh, and read a 1% low as a frame time.
- Mouse polling-rate tester — Measure how often the browser sees pointer events. Average and max Hz.
- Mouse raw input test — See every mouse report as a dot, spot sensor skips, and check jitter, swipe speed, and acceleration.
- Mouse test — Check mouse buttons, the scroll wheel, double-click chatter, and a pointermove polling-rate reading in the browser.
- Keyboard test — Press keys on a US QWERTY board, then time your typing on real sentences or random letter strings.
- Gamepad test — See every controller button, analog trigger and stick live, check stick drift with a suggested deadzone, and test vibration.
- Camera test — Webcam preview, real resolution, measured frame rate and a snapshot.
- Speaker and headset test — Left and right channels, phase, frequency sweep and bass check.
- System info — OS, browser, GPU, CPU threads, RAM and screen your browser reports.
- Keyboard test — Check every key on a US QWERTY board and time your typing.
- Gamepad test — Controller buttons, triggers, sticks and stick drift.
- How a headset microphone picks up sound — Booms, capsules and pickup patterns.
- USB gaming microphones — What a desk USB mic is and when it beats a headset mic.
Comments
No comments yet. Be the first to share what you think.