YuvalGGYuvalGG

Tools

Speaker and headset test

Check that left is left and right is right, find out whether your audio is secretly mono, sweep from 20 Hz to 20 kHz and see how deep your bass goes. Works with headsets, earbuds and desktop speakers.

Speaker and headset test

Every sound here is generated live in your browser with the Web Audio API. No audio files are downloaded and nothing is recorded.

Protect your ears: turn your system or headset volume down before you press play, then raise it slowly. The page starts quiet on purpose. High and low test tones can sound quiet while still being loud, so lower the volume again before you switch tests.
Test sound

1. Left and right

LLeft · silent
RRight · silent

Nothing playing

The coloured fill is the signal the page is sending to each side, not what your headset plays. If the sound comes from the wrong side, or from both sides on Left or Right, see the troubleshooting guide below the tool.

2. Phase (polarity) check

Both play the same sound on both sides. In phase should sit in the middle of your head or between the speakers. Out of phase flips one side, so it usually sounds wide, hollow or hard to place, with less bass on speakers. If in phase is the one that sounds odd, one side is wired backwards somewhere. If out of phase goes almost silent, something is mixing your output to mono, because the two sides cancel out when added together.

3. Frequency sweep, 20 Hz to 20 kHz

—Not playing
20 Hz20 kHz

Rough check only. The result depends on your headset or speakers, the volume, the room and the sound card, so it is not a hearing test. The sweep takes 30 seconds and spends the same time on every octave. Do not turn the volume up to chase the highest tones.

4. Bass check

Start at 150 Hz and work down. Very low tones are felt as much as heard, and small speakers often play them as a buzz or not at all. The slow sweep also shows what rattles on a desk or speaker. Keep the volume low: you cannot judge bass loudness well by ear.

5. Tone generator

Audio output (browser-reported)

Press any test button to start audio. The browser fills in these details then.

These are values the browser reports, not measurements of your headset. Latency is the browser's own estimate and leaves out Bluetooth and some driver delays. Browsers usually mix to stereo, and they only offer more channels when the system output is set up as multichannel. Virtual surround in a headset app or Windows Sonic is applied after the browser, so this page cannot tell whether it is on.

How to use the speaker test

  1. Turn the volume down first. Lower the Windows, macOS or headset volume, then press a test button and raise it slowly until the sound is clear but comfortable.
  2. Press Left and then Right. Each should play on one side only. The L and R panels light up to show which side the page is sending sound to, so you can compare what you see with what you hear.
  3. Press Alternate L / R or Pan sweep to hear the sound jump or glide between sides. On a good stereo setup the pan sweep moves smoothly with no hole or jump in the middle.
  4. Play In phase, then Out of phase. They should sound clearly different. If out of phase nearly vanishes, your output is mixed to mono somewhere.
  5. Run the sweep and the bass check if you want a rough idea of the range your setup plays. Switch between soft noise and a pulsing tone for the left and right checks; noise is often easier to place on speakers.

Sound only in one ear, or the same in both? How to fix it

Run the left and right checks first, so you know which problem you have: one side silent, one side quieter, sides swapped, or both sides playing everything.

On Windows

  • Mono audio. Open Settings, then Accessibility, then Audio, and check that Mono audiois off. On Windows 10 it is under Ease of Access, then Audio. When it is on, every app plays the same mix on both sides, so the Left button plays in both ears.
  • Balance. Open Settings, then System, then Sound, and select your output device. The device page has separate Left channel and Right channel levels on most drivers. Set them to the same value. If they are missing, press Win + R, type mmsys.cpl, open the device's Properties, then Levels, then Balance.
  • The right output. Make sure the device you are wearing is the one selected under Output. A monitor, a dock, a USB dongle and a Bluetooth headset can all appear as separate devices. For Bluetooth, pick the stereo entry, not the hands-free one; my headset setup guide covers why the hands-free entry sounds thin and mono.
  • Processing. On the same device page, try turning off audio enhancements and spatial sound for a moment, and check any headset app or sound card software for its own surround, mono or channel options.

On a Mac

Open System Settings, then Accessibility, then Audio, and make sure Play stereo audio as mono is off. The left and right balance slider is in System Settings, then Sound, under the Output tab.

Cable, jack and headset

  • Push a 3.5 mm plug all the way in. A plug that is half in can drop one side, crackle, or make centred sounds such as voices go quiet while the sides stay loud.
  • Headsets with a microphone usually use a four-contact plug. In some sockets, or through the wrong splitter or adapter, that gives odd results on one side. Try the headset in another port or another device.
  • Wiggle the cable gently near the plug and near the ear cup while the Left or Right test plays. If the sound cuts in and out, the cable or a connection inside the headset is damaged.
  • If one side is silent on every device and every port, the problem is in the headset itself, and the warranty is the next step.

Stereo, virtual surround and what this page can check

Almost every headset has two drivers, one per ear, so it plays two channels: left and right. That is stereo. Games still place sounds around you in stereo by changing the level and timing between your ears, which is why a correct left and right matters so much in shooters. My guide tousing audio in a shooter goes into that.

Virtual surround, such as Windows Sonic for Headphones, Dolby Atmos for Headphones or a headset maker's own surround mode, takes a stereo or multichannel game mix and processes it so it sounds like it comes from around you through two drivers. It is software, applied after the browser and the game, and it can make this test sound wider or move the sound slightly toward the centre. If the left and right checks sound off, turn virtual surround off and test again before blaming the headset.

Real multichannel means separate speakers, such as a 5.1 system with a centre and a subwoofer. Browsers usually output stereo. This page reads how many output channels the browser reports and adds a per-channel test only when it reports more than two, which normally needs the system output set up as 5.1 or 7.1. It cannot see what your speakers or headset do with the signal after that, so the browser-reported details are a starting point, not a spec sheet.

If your headset sounds quiet even at high volume, the drivers' impedance may be part of the reason; seewhat headset impedance means. For tuning the sound after the basics check out, how to set a game EQ is the next stop.

Common questions

How do I test if my left and right headphones are correct?

Put the headset on with the L marking on your left ear, press Left and then Right. Each sound should come from one side only. If Left plays on your right ear, the channels are swapped somewhere between the source and your ears, such as an adapter, a driver setting or the headset worn backwards.

Why do I hear the left test in both ears?

The output is being mixed to mono, or a balance setting is spreading it. Common causes are Mono audio turned on in Windows or macOS accessibility settings, a Bluetooth headset connected in its hands-free call mode, or an app or driver that applies its own mono or surround processing. The out-of-phase check is a quick confirmation: if it goes almost silent, the signal is being mixed to mono.

What does the out-of-phase test do?

It plays the same sound on both sides but flips one side upside down. On correctly wired headphones it sounds wide, hollow or hard to place, and on speakers the bass gets weaker. If it sounds normal and in phase sounds strange instead, one side is wired with reversed polarity. If it nearly disappears, the two sides are being added together into mono and cancel out.

Is the frequency sweep a hearing test?

No. Where you stop hearing the sweep depends on the headset or speakers, the volume, the sound card, the room and your ears all together. Treat it as a rough check of your setup. If you are worried about your hearing, see a hearing professional, who uses calibrated equipment.

Can a browser test 5.1 or 7.1 surround sound?

Only when the system output is set up as multichannel and the browser offers those channels to pages. This page reads how many output channels the browser reports and shows per-channel buttons only when there are more than two. Many headsets present themselves to the system as stereo, and virtual surround is applied after the browser, so a page cannot test it directly.

Why does the low bass tone sound like nothing or like a buzz?

Small drivers struggle to move enough air at very low frequencies, so laptop and phone speakers often play little below around 80 to 100 Hz, and what you hear can be distortion rather than the tone. Over-ear headphones with a good seal usually reach lower. A loose fit or glasses breaking the seal can reduce bass a lot.

Is the volume on this page safe?

The page starts at a low level and its loudest setting stays below full scale, but the final loudness depends on your system volume and your headset. Turn the system volume down before starting, raise it slowly, and lower it again before switching tests, especially before the high and low tones.

  • Sensitivity converter — Convert sensitivity between Overwatch, Valorant, CS2, and other titles using documented yaw values.
  • cm/360 calculator — Turn mouse DPI and in-game sensitivity into centimeters per 360° turn.
  • eDPI calculator — Multiply mouse DPI by in-game sensitivity for a same-game comparison number.
  • FOV converter — Convert horizontal and vertical FOV across 4:3, 16:9, 16:10, and 21:9. Includes Overwatch, CS2, and Valorant.
  • Frame-time and Hz calculator — Convert FPS to milliseconds, compare that wait to the monitor refresh, and read a 1% low as a frame time.
  • Mouse polling-rate tester — Measure how often the browser sees pointer events. Average and max Hz.
  • Mouse raw input test — See every mouse report as a dot, spot sensor skips, and check jitter, swipe speed, and acceleration.
  • Mouse test — Check mouse buttons, the scroll wheel, double-click chatter, and a pointermove polling-rate reading in the browser.
  • Keyboard test — Press keys on a US QWERTY board, then time your typing on real sentences or random letter strings.
  • Gamepad test — See every controller button, analog trigger and stick live, check stick drift with a suggested deadzone, and test vibration.
  • Microphone test — Mic level in dBFS, clipping, waveform, recording playback and background noise.
  • System info — OS, browser, GPU, CPU threads, RAM and screen your browser reports.
  • Keyboard test — Check every key on a US QWERTY board and time your typing.
  • Mouse test — Buttons, scroll wheel, double-click chatter and polling rate.
  • Gamepad test — Controller buttons, triggers, sticks and stick drift.
  • My headset setup — The headset I use for games and why.
  • Open back vs closed back — How the two headset designs differ for sound and isolation.

Comments

No comments yet. Be the first to share what you think.